From the left side, remove the cable that connects the module rack interface board and the 8-slot module rack communication board. Then take off the SMR cover. Unclench the two clips and take out the module rack interface board.
Be sure not to damage the snap slot on the left side. Remove the cable that connects the 8-slot communication board and the LED board, the LED indicator and the light tube. Unclench the clips and take out the Nios II module.
Then unscrew the six M36 screws and remove the 8-slot module rack communication board. Use the sleeve to unscrew the hexagon nut and countersunk external toothed lock washer assembly which can be further separated into the washer, springlet and contact screw. For a reassembled module, a patient leakage current test must be performed before it is used again for patient monitoring. The monitor supports three types of modules, single-slot modules, 2-slot modules and 3-slot modules.
The following part describes two typical disassembling procedures. Unscrew the two contact screws and3 spring washer on the back with a dedicated contact spanner. Move the snap lock in front of the contact spanner to the unlocking position.
Insert a small flat-bladed screwdriver into the hole on the snap lock and press the snap down about 1mm. At the same time, push the snap lock forwards with a thumb until the snap lock and its counterpart separate. Then release the snap lock with a screwdriver. Unscrew the M36 screw. Then press down, in turn, the two clips that engage the front cover.
At the same time, pull off the front cover carefully to avoid damaging the cables. The side cover of the module without the housing is composed of two halves.
Release the three snaps to separate the two halves. Remove the four contact screws on the back and two snap locks on the bottom and then unscrew the two M36 screws by referring to the procedure as described in 5.
Take off the front cover of the CO2 module by referring to the procedure as described in 5. Then press the two clips about 1mm and take off the housing. Hold the housing with both hands. Press the snap side with the thumb and move the other side with the index finger and the middle finger to separate the housing into two halves.
Disconnect the cables from the button board and unscrew the PT38 screw. Then release the two clips and take out the board. After that, disconnect the cable to the fan and remove the button board. Disconnect the tubing that connects the CO2 board and the front cover. Then release four clips and take off the board. It helps the engineer to identify the parts during disassembling the patient monitor and replacing the parts.
Hardware architecture of the main unit is shown below:. Here we list most replaceable parts. If you need more parts, please contact our Customer Service Department. Open navigation menu. Close suggestions Search Search. User Settings. Skip carousel. Carousel Previous. Carousel Next. What is Scribd? Explore Ebooks. Bestsellers Editors' Picks All Ebooks. Explore Audiobooks.
Bestsellers Editors' Picks All audiobooks. Explore Magazines. Editors' Picks All magazines. Explore Podcasts All podcasts. Difficulty Beginner Intermediate Advanced.
Explore Documents. Uploaded by Dodik E. Did you find this document useful? Is this content inappropriate? Report this Document. Description: Patient Monitor Mindray T8. Flag for inappropriate content. Download now. Related titles. Carousel Previous Carousel Next. Jump to Page. Search inside document.
Revision number: 1. All rights reserved. NOTE z Provides application tips or other useful information to ensure that you get the most from your product. Type CF applied part. Defibrillator-proof protection against electric shock. Type BF applied part. The patient monitor also: Provides audible and visual alarm indications in case of patient or equipment problems. Enables displaying, reviewing, storing and transferring of real-time data. Incorporates multiple input devices such as buttons, knob, touchscreen, keyboard and mouse.
Interfaces a clinical information system or central monitoring system. Enables program upgrade over the network. Defibrillator Connector: It is a RJ11 connector used to connect a defibrillator. Secondary USB Connector: used to connect the mouse and keyboard of the secondary display. Power module Converts the input power into voltages that fit each module and then forwards them to each module.
CPU Control the communications between modules. Signal interfac Control the communications between the main board and the recorder CPU. Motor drive circuit Receives the control signals from the CPU and then forwards them to the step engine. The mother board is in charge of connections and communications with other components and provides the following interfaces: LCD port: connects a built-in display.
Button board port: connects the button board. Integral module rack port: connects integral module rack communication board. Fan port: connects the fan. Speaker port: connects the speaker. Power module port: connects the power module. Recorder port: connects the recorder. Operating principle of the communication board is as follows: The infrared circuit transmits and receives infrared signals, and controls signal intensity; RS communication circuit implements signal conversion between serial signals and RS signals; Power circuit transfers 3.
NOTE z Two batteries must be used simultaneously when the patient monitor operates on battery power. Black RXD Receives serial communications the main board sends. Purple TXD Sends serial communications the main board receives. Red 18, 19 3. BNC connector Outputs analog signals and nurse call signals. RJ 11 connector Outputs defibrillator synchronization signals. DVI-D connector Connects a secondary display. It has the following features: It allows a parameter module to be plugged and unplugged with the patient monitor on.
The following diagram shows the structure of the SMR. Power on test 1. Mainstream CO2 test 1. If user suspects that the measurement is incorrect. Sidestream and Microstream CO2 tests Leakage test 2.
Following any repairs or replacement of respective module. ECG tests Performance test Calibration 3. At least once every two years.
Calibration 2. Nurse call relay performance test Analog output performance test Electrical safety tests Enclosure leakage current test 1. Following any repair or replacement of the power module. Earth leakage current test 2. Patient leakage current test Patient auxiliary current test Touchscreen calibration Recorder check 1. Follow these guidelines when inspecting the equipment: Carefully inspect the case, the display screen and the buttons for physical damage to Inspect the SMR and parameter modules for mechanical damage.
Inspect all external connections for loose connectors, bent pins or frayed cables. Inspect all connectors on the equipment for loose connectors or bent pins. Make sure that safety labels and data plates on the equipment are clearly legible. The patient monitor enters the main screen and start-up is finished.
Connect the mainstream CO2 module with the sensor and plug the module in the module rack. Plug the module in the module rack. Block the gas inlet completely. Make sure that the CO2 module has been warmed up or started up. In the [Maintain CO2] menu, select [Zero]. Open to the air Gas valve Tubing Monitor Gas bottle 5.
Vent the tubing to the CO2 opening the gas valve. Connect the patient simulator to the Resp connector on the module. The displayed Resp value should be 40 2 rpm. Apply the cuff to the cylinder as shown below. The cuff automatically deflates in 20s which means NIBP leakage test is completed. Connect the equipment as shown below.
Connect the patient simulator to the pressure connector on the module. Set the pressure value of patient simulator to 0. Press the Zero Key on the module to start a zero calibration. The displayed value should be 2 mmHg. If the value is beyond tolerance, calibrate the pressure module. Connect the equipment as shown below Pressure transducer 3-way stopcock T-shape connector Pressure adapter cable IBP module Manomete 2.
Zero the transducer. After a successful zero, open the stopcock to the manometer. Adjust the preset calibration value until it equals to the reading on the manometer. The displayed SpO2 and PR values should be within the ranges listed below.
Test Tool required: Patient simulator 1. Connect the patient simulator to the C. The displayed BIS value should be higher than Calibrate the flow sensor. Switch the patient simulator to Mode 1 and then start ICG measurements. Check that measured values meet the simulator configuration 3. AG Calibration Tools required: Gas bottle, with a certain standard gas or mixture gas. T-shape connector Tubing Reservoir bag Follow this procedure to perform the calibration: 1. Check the airway and make sure that there are no occlusions or leaks.
Open the gas valve and vent a certain standard gas or mixture gas. Select [Start] to start calibration. Connect the nurse call cable to the Auxiliary Output Connector of the patient monitor. Set [Contact Type] to [Normally Open] 4. Connect the oscillograph to the Auxiliary Output Connector of the patient monitor. These electrical safety tests do not supersede local requirements. Connect the safety analyzer to an AC power supply V, 60 Hz.
Connect the EUT to the analyzers auxiliary output connector using a power cord. Connect the safety analyzer to an AC source V, 60 Hz. The 3. Select, in turn, the central point of the 4. Print ECG waveforms. The recorder should print correctly and printout should be clear.
Color: selecting Color will have smoother waveforms. Mono: selecting Mono will have a wider viewing angle. The display of [Software Version] menu is as follows: 3. Monitor information is displayed as follows: 3. Through the network or by connecting the patient monitor to a PC via a crossover network cable, you can upgrade the following programs: Boot program System program Multilingual library BMP files including screen icons, start-up screens, standby screens General configurations including passwords, company logo System functional configuration FPGA program Integral module rack program Satellite module rack program Parameter module programs: MPM, IBP module, C.
Program upgrade should be performed by qualified service personnel only. NOTE z After upgrading the boot program, re-upgrade the system program and other programs to ensure compatibility. Power supply protection Refer to 4. Cables defective or poorly connected 1. Power module defective Replace the power module. Mother board Defective Replace the mother board.
Cables defective or poorly connected. Secondary display does not function. Secondary display displays snows or flashing specks Images overlapped or distorted 2. Backlight board defective Replace the backlight board. Display defective Replace the display. The mother board is damaged. Replace the mother board. FPGA error. Update or upgrade FPGA. Touchscreen does not response Touchscreen disabled Check if there is a symbol shown above the [Measurements] QuickKey.
Check that the cables and connectors are properly connected Touch position invalid Touchscreen control board defective Replace the touchscreen control board Button board defective. Replace the button board. Touchscreen defective. Replace the touchscreen Mother board defective Replace the mother board Touchscreen not calibrated Calibrate the touchscreen 4.
Defective parameter module Replace the suspicious parameter module with a known good module. Wrong communication board software revision Upgrade the program of the module or SMR.
Module in some slots unrecognized 1. Cable defective or poorly connected 1. Nios II module loose or failure 1. Mother board failure Replace the mother board. If the symptom persists, replace the Nios II module.
Integral module rack Integral module rack cannot identify parameter modules Module failure Replace parameter module. Wrong communication board software revision Upgrade the program of the module or Integral module rack. Module in some slots unrecognized 3. No alarm sound is issued but alarm lamp is light 2.
Button board failure Replace the button board. Speaker failure Replace the speaker. Knob does not work Button board failure Replace button board. Knob failure Replace the knob encoder. Button board failure Replace the button board 4.
Check that cable between recorder and mother board is properly connected. Recorder failure Replace the recorder. Paper roll not properly installed Stop the recorder and re-install the paper roll.
Print head dirty 1. Recorder failure Replace recorder. DVI interface board cable loose 1. CF card board failure Replace the CF card board. Battery capacity is too low Power board failure Replace the power board.
Battery failure Replace battery. Battery cannot be recharged Power board failure Replace the power board. Battery failure Replace battery and recharge the replacement battery. Turn off the monitor then restart it.
If the problem still remains, replace power board. NOTE z When the power module has a failure, it may cause problems to other components, e. No connection to LAN 1. CIS assembly failure 1. LAN cable shall not be longer than 50 m. Reconfigure IP address. LAN cable shall not be longer than 50m. Excessive requests for viewing the patient monitor at the same time A patient monitor can only be viewed by 4 other patient monitors at the same time under the View Others mode.
Program upgrade fails Incorrect network connection 1. Wrong upgrade package has been downloaded Upgrade package shall be. Disconnect the AC power source and take out both of the batteries. Put the cables or wires in place when reassemble the monitor to avoid short circuit.
Place the monitor face up and unscrew the four M screws, as shown in the figure below. NOTE z Exercise care when pulling the base out. Be sure not to damage the cables and connectors. Press the cover with a thumb when prying it. Lift the rear cover assembly to separate it from the front cover assembly. Left Clip Right Clip 2. NOTE z Exercise care whe releasing the clips. Locate the cables marked in the picture and disconnect them from the button board. Unscrew the three PT38 screws and take out the button board.
Disassemble the LCD screen in an environment as dust-free as possible. Disconnect the cables that connect the following parts. The backlight board and the button board. The touchscreen control board and the button board.
The alarm lamp board and the button board. NOTE z Exercise care when removing the alarm lamp board because it may be adhered to the LCD assembly as shown in the upper-right figure. Battery 5. Unscrew the four M36 screws and remove the interface board assembly. If a conventional keyboard is connected to the monitor, you can use it instead of or in combination with the on-screen keyboard. The patient monitor supports two external keyboards.
One is for controlling the secondary display and must be connected to a dedicated USB connector, and the other for controlling the primary display and can be connected to any USB connector other than that dedicated one.
A padlock symbol is displayed if if. Most of monitor operations and settings can be performed through the main menu. Heading: gives a sum-up for the current menu. Main body: displays options, buttons, prompt messages, etc. Online help area: displays help information for the screen item to which the cursor points. A CF storage card is used to prevent data loss in case of a sudden power failure.
The patient data such as trend data, waveform data, etc. In case of a sudden power failure, the patient data can be retrieved from the CF storage card after the patient monitor restarts.
Switching the patient monitor off before inserting or removing a CF card is a must. To insert a CF storage card, open the compartment on the left side and then insert the card until the button flips out. To remove the CF storage card, take the stick and use it to press the button until the CF storage card flips out.
Select a patient whose data you want to view from the [ Patient Data List ] and then select [ Review ]. In the [ Review ] menu, select the data you want to review. Otherwise it may cause damage to the CF storage card and the patient monitor.
This chapter covers only general settings such as language, brightness, date and time, etc. Measurement settings and other settings can be referred to in respective sections. In the [ User Maintenance ] menu, select [ Language ] and then select the desired language. Restart the patient monitor. Select the appropriate setting for the screen brightness.
If the patient monitor operates on battery power, you can set a less bright screen to prolong. When the patient monitor enters standby mode, the screen brightness will be adjusted to the least bright automatically. The patient monitor provides online help information.
The user can display or hide the help as required. Select [ Help ] and toggle between [ On ] and [ Off ]. Select [ Date Format ] and toggle between [ yyyy-mm-dd ], [ mm-dd-yyyy ] and [ dd-mm-yyyy ]. Select [ Time Format ] and toggle between [ 24h ] and [ 12h ]. If your patient monitor is connected to a central monitoring system CMS , the date and time are automatically taken from that CMS.
In that case, you cannot change the date and time settings on your patient monitor. Select [ Alarm Volume ] and then select the appropriate volume. Select [ Key Volume ] and then select the appropriate volume.
The pitch of the tone rises as the saturation level increases and falls as the saturation level decreases. The volume of this tone is user adjustable. Select [ Beat Vol ] and then select the appropriate volume.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. BeneView T8. Contents 1 Safety A-1 A. A-4 A. A-5 A. A-8 A. A-9 B EMC B-1 C Factory Defaults C-1 C. C-2 C. C-3 C. C-4 C. C-5 C. C-6 C. C-7 C. C-8 C. C-9 C. C C. C D Alarm Messages D-1 D. D-2 D. D-3 E Symbols and Abbreviations E-1 E. Safety 1.
Physiological alarm lamp When a physiological alarm occurs, this lamp will flash as defined below. High level alarms: the lamp quickly flashes red. Medium level alarms: the lamp slowly flashes yellow. Low level alarms: the lamp turns yellow without flashing. Technical alarm lamp This lamp will turn blue when a technical alarm occurs. Display Screen 4. Battery LED On: when the battery is being charged or already fully charged.
Off: when no battery is installed or no AC source is connected. Flash: when the patient monitor operates on battery power. Press to silence all system sounds. Press to pause, restore or clear alarms. Press to freeze or unfreeze waveforms. Press to start or stop recordings. Press to start or stop NIBP measurements. If no menu is displayed on the screen, pressing it will enter the main menu.
If there is a menu displayed on the screen, pressing it will close that menu. Knob As shown in the figure, you can: Rotate the knob clockwise or anti-clockwise. With each click, the highlight jumps to the neighboring screen item, or When you reach the desired screen item, press the knob to select the item.
The Basics 2. Integral Module Racks 2. Compartment for CF storage card slot 3. Recorder 4. Filter 5. AC Power Input 2.
Auxiliary Output Connector It provides analog signals if an oscilloscope is connected or alarm signals if a nurse call system is connected. Defib Sync Connector It provides synchronization signals if a defibrillator is connected. Equipotential Grounding Terminal When the patient monitor and other devices are to be used together, their equipotential grounding terminals should be connected together, eliminating the potential difference between them.
Invasive blood pressure module. Cardiac output module. Carbon dioxide module. Impedance cardiography module. Bispectral index module. Respiration mechanics module. Module name 2. Indicator On: when the patient monitor works correctly.
Flash: when the module is plugged into the patient monitor. Off: when the module is either not in place or broken. Measurement connectors. Patient Information Area This area shows the patient information such as department, bed number, patient name, patient category and paced status. Date and Time This area shows the system time of the patient monitor. Sound Symbols indicates alarms are paused. Technical Alarm Area This area shows technical alarm messages and prompt messages.
Physiological Alarm Area This area shows physiological alarm messages. Waveform Area This area shows measurement waveforms. Parameter Area This area shows measurement parameters. Prompt Message Area This area shows the prompt messages telling the network status, battery status, etc. QuickKeys area This area contains QuickKeys that give you fast access to functions. By default, the following QuickKeys are displayed on the screen: Scroll left to display more QuickKeys.
Scroll right to display more QuickKeys. Besides the default QuickKeys listed above, there are still more QuickKeys: Change alarm settings Quickly admit a patient Re-learn arrhythmia.
Basic Operations 3. NOTE z Save the packing case and packaging material as they can be used if the equipment must be reshipped. WARNING z Do not use the patient monitor for any monitoring procedure on a patient if you suspect it is not working properly, or if it is mechanically damaged. When you are using a mice: By default, the left mice-button is the primary button and the right one the secondary button. The secondary button is disabled. You can also define the right mice button as the primary button by following this procedure: 1.
You can enable or disable touchscreen operation by pressing and holding the [ Measurements] QuickKey for 3 seconds. A padlock symbol is displayed if if touchscreen operation is disabled. Basic Operations the use time of the battery. Set the date and time. Key Volume 1. You can only view or download manuals with.
Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual. Buy as many as you need. View and download manuals available only for.
Register and get 5 for free. Upload manuals that we do not have and get 1 for each file. Get 1 for every download of your manual. Page 14 Contents Page 15 Contents Page 16 Contents Page 17 Contents Page 18 Contents A-1 A. A-4 A. A-5 A. A-8 A. A-9 B EMC B-1 C Factory Defaults C-1 C. Page Safety Safety 1. Page Dangers Safety 1. Page Cautions Safety 1. At the end of its service life, the equipment, as well as its accessories, must be disposed of in compliance with the guidelines regulating the disposal of such products.
Page Equipment Symbols Safety 1. Page Reference Literature Safety 1. Page The Basics The Basics 2. Page Main Unit The Basics 2.
High level alarms: the lamp quickly flashes red. Medium level alarms: the lamp slowly flashes yellow. Low level alarms: the lamp turns yellow without flashing. Press it again and hold for 2 seconds to turn the patient monitor off.
An indicator is built in this switch. It turns on when the patient monitor is on and turns off when the patient monitor is off. Page Side View The Basics 2. Integral Module Racks 2. Compartment for CF storage card slot 3. Recorder 4. Filter 5. Page Rear View The Basics 2. Auxiliary Output Connector It provides analog signals if an oscilloscope is connected or alarm signals if a nurse call system is connected. Defib Sync Connector It provides synchronization signals if a defibrillator is connected.
The number of modules mounted in the SMR depends, as different modules may need different slots. Page Modules The Basics 2. Invasive blood pressure module. IBP module: Cardiac output module. As shown below, the module name is located at the upper left corner, all hardkeys on the upper part, and all measurement connectors on the lower part. Other measurement modules look similar to the MPM.
Page Display Screen The Basics 2. A typical display screen is shown below. Patient Information Area This area shows the patient information such as department, bed number, patient name, patient category and paced status.
By selecting this area, you can enter the [System Time] setup menu. Sound Symbols indicates alarms are paused. Page Quickkeys The Basics indicates patient monitor is connected to a wire network successfully. QuickKeys area This area contains QuickKeys that give you fast access to functions.
Page Basic Operations Basic Operations 3. The software copyright of the equipment is solely owned by us. No organization or individual shall resort to juggling, copying, or exchanging it or to any other infringement on it in any form or by any means without due permission. If any damage is detected, contact the carrier or us. If the packing case is intact, open the package and remove the equipment and accessories carefully.
Page Environmental Requirements Basic Operations 3. The environment where the patient monitor is used shall be reasonably free from noises, vibration, dust, corrosive, flammable and explosive substances. If the patient monitor is installed in a cabinet, sufficient space in front and behind shall be left for convenient operation, maintenance and repair.
Page Getting Started Basic Operations 3. Disconnect the patient cables and sensors from the patient monitor. Make sure to save or clear the patient monitoring data as required.
The USB mice can be plugged and unplugged with the monitor on. The patient monitor supports two USB mice. One is for controlling the secondary display and must be connected to a dedicated connector, and the other for controlling the primary display and can be connected to any USB connector other than that dedicated one. Page Using Keyboards Basic Operations 3. Use the [Back] key to delete the previously entered character.
Use the [Caps] to toggle between uppercase and lowercase letters. Select [Enter] to confirm what you have entered and close the on-screen keyboard. If a conventional keyboard is connected to the monitor, you can use it instead of or in combination with the on-screen keyboard. Most of monitor operations and settings can be performed through the main menu.
Other menus are similar to the main menu and contain the following parts: Heading: gives a sum-up for the current menu. The patient data such as trend data, waveform data, etc. Otherwise it may cause damage to the CF storage card and the patient monitor. Never apply the CF storage card to those other than the patient monitor. When the patient monitor enters standby mode, the screen brightness will be adjusted to the least bright automatically.
The user can display or hide the help as required. Page Adjusting Volume Basic Operations 3. Select [Alarm Volume] and then select the appropriate volume. Select [Key Volume] and then select the appropriate volume. Page Default Configurations Basic Operations 3. Select a user default configuration you want to apply and then select [Ok]. Select [Yes] from the popup menu. Make sure the configuration is appropriate.
Page Managing Patients Managing Patients 4. This allows you to monitor a patient that is not yet admitted. However, it is recommended that you fully admit a patient so that you can clearly identify your patient, on recordings, reports and networking devices.
If you do not specify settings for these fields, the patient monitor uses the default settings from the current configuration, which might not be correct for your patient.
Select [Patient Demographics] and then make the required changes. All patient information, measurement data and settings can be displayed simultaneously on the patient monitor and CMS.
Page User Screens User Screens 5. Changing some settings may be hazardous. Therefore, those setting are password-protected and can be modified by authorized personnel only. Select the required parameters from the popup menu.
Close the popup menu, and your selections will be automatically applied. Additionally, you can close a waveform or turn off a measurement.
Page Viewing Minitrends User Screen 5. In the [Minitrend Setup] menu, select [Minitrend Length] and then choose [1 h], [2 h], [4 h] or [8 h]. Select the button. Page Viewing Oxycrg User Screen 5. The split-screen view covers the lower part of the waveform area and shows HR trend, trend and RR trend or Resp wave.
This lets you: View information on the monitor screen from other bed in the same. Be notified of physiological and technical alarm conditions of other beds in the Care Group. Page 63 User Screen The [View Other Patient] window covers the lower part of the waveform area and consists Information Area: shows the patient information including department, bed number, patient name, etc. View Area: shows physiological waveforms and parameters. This area contains four areas, two waveforms areas and two parameter areas.
You can select your desired parameters to display in this screen: select the [Para. Setup] QuickKey and then select the parameters you want. Page Alarms Alarms Alarms, triggered by a vital sign that appears abnormal or by technical problems of the patient monitor, are indicated to the user by visual and audible alarm indications.
Page Alarm Levels Alarms 6. High level alarms Indicate that your patient is in a life threatening situation and an emergency treatment is demanded. Page Alarm Indicators Alarms 6. Alarm lamp Alarm message Flashing numeric Audible alarm tones 6. If a physiological alarm occurs, the physiological alarm lamp will flash. Page Flashing Numeric Alarms 6.
Page Alarm Tone Configuration Alarms 6. Page Using Alarms Alarms 6. Select [Alarm] and toggle between [On] and [Off]. Page Recording Alarms Automatically Alarms 6. To switch automatic start of alarm recording on or off for individual measurements, you can either: In the setup menu for your desired measurement, select [Alm Rec] and toggle between [On] and [Off], or Page Pausing Alarms Alarms 6.
When alarms are paused: No alarm lamps flash and no alarms are sounded. No numeric and alarm limit flash. No alarm messages are shown. Page Clearing Technical Alarms Alarms numeric and violated alarm limit stop flashing as soon as the initial alarm condition goes away. Select [Latching Alarms] and toggle between [Yes] and [No]. Technical alarms are always non-latching. In particular, make sure that all of the ECG electrodes are attached to the patient, to prevent them from contacting conductive parts or earth.
Proper skin preparation is necessary for good signal quality at the electrode, as the skin is a poor conductor of electricity. To properly prepare the skin, choose flat, non-muscular areas and then follow this procedure: Shave hair from skin at chosen sites.
Select [Lead Set] and then select [3-lead], [5-lead] or [lead] according to the applied electrodes. V placement: on the chest. The chest V electrode can be placed on one of the following positions: V1 placement: on the fourth intercostal space at the right sternal border. V2 placement: on the fourth intercostal space at the left sternal border. Lead Placement for Surgical Patients The surgical site should be taken into consideration when placing electrodes on a surgical patient.
Your display may be configured to look slightly different. By selecting any ECG wave, you can enter its lead menu. Filter settings do not affect ST measurement. To change the filter setting, select [Filter] from [ECG Setup] and then select the appropriate setting.
Select [Defib. Sync] and toggle between [On] and [Off]. You should choose a lead of best quality signals as the HR lead. To select a lead as the HR lead, in [Normal] screen, select the wave corresponding to the HR parameter to enter its lead menu. The default setting is off. ST segment analysis calculates ST segment elevations and depressions for individual leads and then displays them as numerics in the ST1 and ST2 areas.
A positive value indicates ST segment elevation; Alarm limits can also be set separately for single-lead and multi-lead ST monitoring. Select [Arrh. In the [Arrh. Review] window, you can: Select [Index] and then set a time as the index for finding your desired arrhythmia events.
There are totally 12 ECG waves and 1 rhythm wave displayed on the screen. In this review window, you can: Select a set of lead ECG analysis results for viewing. This window displays a set of lead ECG analysis results only.
Gain Resp lead label Respiration rate By selecting the waveform area, you can enter the [Resp Waveform] menu. By selecting the Resp parameter window, you can enter the [Resp Setup] menu.
0コメント